We all need that assurance that our property is safe. You should not only get insurance but also make sure that you have kept the things themselves in a safe place. This is why when you are especially traveling, you should have your custom road cases. These will always ensure that your property is safe from all kinds of weather.
You need to set up a place where you will be spending most of your time building the case. You should make sure that you have all the equipment you need in order to move the process along faster. Make sure that you have a cut list to avoid wasting any material. You are to build the case according to the size of the item you are building the case for.
You will need to cut your aluminum into pieces. Using a hot saw may cause damage to it. A cold saw, however, is recommended. The aluminum is one of the materials that causes the case to be very strong. You should use a piece of an uncut u-channel to measure the length of the other side pieces you may need. The measurements should be in line with the items you will be storing inside.
The next step is to make the pockets and notches of the case. These are made out of wood and it should, therefore, be not too difficult to use make them. You will need to mark the cut points and you should, therefore, use the unfinished side of the ABS. Afterward, you should reduce the size of the u-channels to match the sizes of the notches.
You need to attach the corners. These corners allow your case to hold everything together and better still keep the road in a square shape. These corners are not held by screws or nails but rather by rivets. You can use a hand rivet gun to put the rivets in place but if possible, get a pneumatic riveter. It so happens to be more efficient.
After putting in the ball corners, the straight ones should be next. These allow the road to stand upright. You will need to drill some holes and put in some screw in order for the pieces of the road to come together. You can start by putting in a screw in every end then proceed for round two as a way of reinforcement.
Depending on what you keep inside, the case may be heavy or light. If it is heavy, you may want it to have a wheeled bottom to push it around. In case it is a light one, you may go for a rubber bottom to protect it from dirt and even moist surfaces. As you assemble the case, it should be in a closed position to avoid placing hinges in the wrong places.
All the cases you may have come across usually have foam dented in the shape of what is kept inside. You too need this foam in your case. It absorbs the shock and adds to the elegance. You should make sure the walls are not fully covered to avoid trouble while closing the road.
You need to set up a place where you will be spending most of your time building the case. You should make sure that you have all the equipment you need in order to move the process along faster. Make sure that you have a cut list to avoid wasting any material. You are to build the case according to the size of the item you are building the case for.
You will need to cut your aluminum into pieces. Using a hot saw may cause damage to it. A cold saw, however, is recommended. The aluminum is one of the materials that causes the case to be very strong. You should use a piece of an uncut u-channel to measure the length of the other side pieces you may need. The measurements should be in line with the items you will be storing inside.
The next step is to make the pockets and notches of the case. These are made out of wood and it should, therefore, be not too difficult to use make them. You will need to mark the cut points and you should, therefore, use the unfinished side of the ABS. Afterward, you should reduce the size of the u-channels to match the sizes of the notches.
You need to attach the corners. These corners allow your case to hold everything together and better still keep the road in a square shape. These corners are not held by screws or nails but rather by rivets. You can use a hand rivet gun to put the rivets in place but if possible, get a pneumatic riveter. It so happens to be more efficient.
After putting in the ball corners, the straight ones should be next. These allow the road to stand upright. You will need to drill some holes and put in some screw in order for the pieces of the road to come together. You can start by putting in a screw in every end then proceed for round two as a way of reinforcement.
Depending on what you keep inside, the case may be heavy or light. If it is heavy, you may want it to have a wheeled bottom to push it around. In case it is a light one, you may go for a rubber bottom to protect it from dirt and even moist surfaces. As you assemble the case, it should be in a closed position to avoid placing hinges in the wrong places.
All the cases you may have come across usually have foam dented in the shape of what is kept inside. You too need this foam in your case. It absorbs the shock and adds to the elegance. You should make sure the walls are not fully covered to avoid trouble while closing the road.
About the Author:
You can find a detailed overview of the benefits you get when you order custom road cases at http://www.encorecases.com/products right now.
Tidak ada komentar:
Posting Komentar